8919 New Falls Rd,

Levittown, PA 19054

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

8919 New Falls Rd,

Levittown, PA 19054

Increase Water Pressure: 5 Good Techniques

Low Water Pressure In Your House? Quick Fixes…

A bad shower to begin and end a long day is very awful. Still, when other residential property repair work take preference, you from time to time have to learn to cope with low water pressure.

 

Fix to fully acquire a good stream of water by attempting any of the approaches listed below, which vary from little adjustments to massive jobs.

Speak with Your Next-door neighbors

First and foremost: Contact your neighbors to see if they are having a similar issue.  The problem might be with the city’s public water supply if this is the case.

 

These systems, like your house’s piping, are prone to leaks, blockages, accumulation, and deterioration.

Rusted Damaged Shut-off Water Valve

Q: What is the reason for low water pressure? Can I fix it myself?

A: The average water pressure at a house’s inlet valve should be around 40 to 50 psi. Your residence might still have lower water pressure than wanted for a variety of reasons.

 

  • Where you detect it can assist you figure out what’s triggering the problem and whether or not you can fix it yourself.

 

  • Low water pressure in your region, for example, is most likely a problem that needs to be addressed by the town utility.

 

  • Whereas, low water pressure at a specific appliance can normally be traced down to a stopped up aerator or a leak in the water line going to the appliance.

Some jobs are better left to the pros

Consult a Pro. Get No-Commitment Estimates For Your Project.

Check the Water Pressure Yourself

You can test the city water pressure yourself before calling your local company by using a test gauge with a hose connector.

 

Simply screw the gadget onto a hose faucet and switch on the water, after turning off the rest of your property’s faucets and any water-using appliances (such as the dishwashing machine and washing machine).

Specialist plumbers say that readings of 45 or 50 psi are on the low side, 60 is a good reading, and 80 or greater is extreme.

 

You can choose what actions to take next after you have either dismissed or validated a pressure problem.

Clear the Obstructions

Mineral deposits can build in your pipes over time. In severe cases, the diameter of the pipes shrinks to the point that they get blocked, preventing water from freely flowing.

 

Leaving you with a pitiful drip in the shower or a small trickle from the faucet.

 

While extreme cases might require the replacement of areas of pipe, you might at minimum prevent blockages at your system’s exit points. Clearing up and dissolving any minerals that are clogging the inside faucet fittings and shower heads will certainly help.

 

Here is how: Simply lay an open zip-lock bag filled with vinegar over your shower head or faucet, secure it with string, and leave it to soak over night. The next day all that requires to be done is rinse off your cleared up fittings.

Contact a local plumber to take a look at and fix the problem if this approach does not work and you presume a more major mineral clog inside the pipelines.

Completely Opened

The following technique takes just a couple of minutes of research. The stream of water into your property’s pipelines is controlled by the main water valve, which is normally found near the meter.

 

Make sure and find the valve that it is entirely open.

 

If, for example, your pressure drop might be because of a current property improvement work. Your contractor might have cut off the main water supply and simply partially reopened the valve at the end of the task.

 

As a result, stream is restricted and pressure is lowered. You can adjust the valve yourself, avoiding the need for a plumbing company.

Water Intake Valve Regulator

Change the Regulator

Plenty of properties that use public water have a regulator, which is either set up at the meter or where the service line goes into the property and ensures that water does not rush through the pipelines.

 

When the regulator fails, the pressure goes down, leading to a loss of speed that impacts some or all of your property’s components.

 

To fix the issue, either change this part or reset or even better, work with a plumbing company to manage the job for you.

Check for Leaks

Water leaks triggered by split or damaged pipes can draw out water as it flows through your pipes. Leaving you with just a drip at the faucet.

 

To inspect if your main pipe is damaged, turn off all faucets inside and out, then turn off the water valve in your home and jot down the number that displays on your water meter.

Return in two hours and take another reading from the meter. Increasing reading suggests a leak and might indicate that it is time to hire a pro.

Galvanized steel pipes are more prone to deterioration over time, so if you choose to change them, go with superior plastic or copper pipes. You should not feel obligated to do this particular repair work yourself:

 

Pipe replacement requires the services of an experienced plumbing professional. While it is a pricey project, replacing your pipelines will do more than just improve your bathing experience.

 

In addition to increasing pressure and minimizing the probability of future leaks, replacing old pipes with brand-new can decrease the possibility of corrosives contaminating your drinking water, leading to better quality water.

Install a Booster Pump for Water Pressure

It’s possible that the issue isn’t with your plumbing system, but with in the area. Gravity and distance are two significant issues that decrease water pressure.

 

The pressure might be reduced if your property water supply is forced to travel uphill or a long distance from the municipal water source.

Low Pressure Water Booster

When it reaches your property, consider adding in a water pressure booster pump to boost the stream rate of the water.

 

The pump costs around $200 or $300, not including the expense of setup which is (better entrusted to a certified plumbing professional).

Some jobs are better left to the pros...

Get No-Commitment Estimates For Your Project

Proud to Install, Repair, and Service the Following Brands: