8919 New Falls Rd,

Levittown, PA 19054

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

Mon-Sat 7:00am-7:00pm

Sunday 10:00am-6:00pm

8919 New Falls Rd,

Levittown, PA 19054

Weekend Plumber? 13 Plumbing Tricks of the Profession

A couple of DIY plumbing pro-tips to help you succeed and make your life a little less complicated

More than any other type of home improvement job, plumbing can drive a DIYer crazy. Issues occur, projects grow, and frustrations increase. Even pros are not immune. Yet one way to take care of the frustrations and accomplish a successful plumbing job is to enable plenty of time at the very least two times as much time as you assume the job should take.

 

One more smart step is to know some tricks of the trade. Here are a couple of favorites from a local plumber in [county], [region].

Reheat Solder When You Can't Cut a Pipe-weekend-plumber

Reheat Solder When You Can Not Cut a Pipe

The best solution to disconnect a soldered pipeline is to cut it. Yet often you can not– either because you can not get a cutting device near the space or because cutting would leave the pipeline way too short to make a brand-new hookup.

 

The solution is to heat the joint and pull off the fitting as the solder melts.

 

Have a damp rag ready and quickly clean away the molten solder before it hardens. (Wear gloves to avoid burning your fingers!) In some cases a quick wipe will leave the pipeline prepared for a brand-new fitting.

 

Very likely, you’ll have to scour off some excess solder with sandpaper or emery cloth before you can slip on a brand-new fitting.

Replace Metal Drain Lines with Plastic

Replace Metal Drainpipe Lines with Plastic

Metal drainpipe lines under sinks look a whole lot more reliable than plastic. Yet plastic is much better in almost every way. It’s less expensive, less complicated to install, and a lot easier to readjust or tighten if a leak forms. And unlike metal, plastic will not corrode.

 

So when a metal drainpipe leaks, usually the smartest move is to change the whole installation with plastic.

Loosen Stuck Water Lines with Heat

When a threaded hookup will not move, using heat often works, especially on old connections that were sealed with pipeline dope that hardened with time. Be patient. Getting the metal hot sufficient can take a number of minutes.

 

Guard nearby surface areas with a flame-resistant cloth. This technique is for water and waste pipes only, never for gas or gas lines.

Some jobs are better left to the pros...

Get No-Commitment Estimates For Your Project.

Piggyback Stubborn Shutoffs

Shutoff valves under sinks and toilets have a rotten reliability history. Often they will not close totally; at times they will not close at all. In either case, there’s an alternative to replacing the shutoff.

 

The majority of home centers carry “piggyback” shutoff valves that attach to existing shutoffs. Simply separate the supply line and install the brand-new valve (a brand-new supply line is a good suggestion, too). If the old shutoff shuts much of the way, you will not even have to turn off the main water valve; simply set a container under the valve to catch the drip while you do the job.

Fix a Clog in Seconds

Deal with a Block in Seconds

Before you run a drainpipe snake inside a blocked pipeline or dismantle the trap, there are a couple of other tricks worth attempting: Often, you can yank out a block with a flexible-shaft pick-up device, or even a Zip-It jig can likewise do the trick.

 

Likewise, a wet/dry vacuum cleaner just may suck out the obstruction.

 

A clogged drain or toilet can be triggered by the accumulation of hair, soap scum and even foreign things such as hairpin or cotton swabs. If you have a blocked sink or toilet, you can use a plunger to try unclogging it.

 

If the blockage is too far down the pipelines or you are unable to solve it on your own, contact a plumber near me. Our specialists will clear your clogged drain pipes and, if necessary, repair them.

 

Are you having problems with drains in your home? 

Don't Overtighten Supply Lines

Don’t Overtighten Supply Lines

It’s tempting to crank supply lines on tight, solely to be safe. Yet overtightening supply lines is actually riskier than under-tightening. A loose hookup that drips is easy to tighten, however overtightening can damage rubber seals and split the threaded nuts.

 

So start this habit: Make the connections at both ends of the supply line finger-tight, then give them an additional one-eighth to one-quarter turn with pliers. If they drip, snug them up a little bit more.

Don’t Reuse Supply Lines

When you’re replacing a toilet or a faucet, you can save a couple of dollars by reusing the old flexible supply water lines. Yet don’t. Plastic deteriorates gradually, and perhaps even a little drip can result in devastating water damages. It’s a small risk, but not one worth taking.

 

A best practice is to get brand-new lines that are wrapped in braided stainless steel; they’re much less likely to ruptured. Yet even if you already have braided lines that are several years old, change them.

Tips for Using Thread Tape

Tape and dope are similarly reliable for sealing pipeline threads. The primary benefit of tape is that it will not smear onto your hands or tools and end up on the carpet. Below are some suggestions for tape:

 

  •  Affordable tape functions fine, however, the thicker stuff (typically pink for water, yellow for gas) is much easier to manage and rips more neatly.
  • Unlike dope, the tape is for pipeline threads only. Don’t use it on compression or other connections
  • How many times should you wrap around the pipeline? There are no guidelines, however, the most common reply from professional plumbing technicians was three.
  • Always wind the tape clockwise around the threads. Otherwise, the tape will unwrap as you screw the joint together.

Cut Stubborn Components

Rust and mineral deposits have a remarkable power to secure parts together, making them almost impossible to separate. Often, the very best solution is to cut the stubborn element.

 

Either slice it off or cut kerfs in the element so you can break it off. A hacksaw blade functions well. Oscillating or rotary tools work perhaps even much better.

Choose Caulk, Not Putty

Select Caulk, Not Putty

Regardless of the name, our plumbing technicians hardly ever make use of plumber’s putty. It harms some types of plastic and stains surface areas such as natural rock. And also, it is likely to dry, split and allow leaks.

 

Silicone caulk is a much safer, longer-lasting sealer in most places where you may make use of plumber’s putty.

Dope Everything

Use Dope On Everything

Thread sealer (also known as ‘pipeline dope’) is designed to secure threads. Yet it’s excellent for almost any kind of hookup, even if the threads don’t form the seal. Utilize it on compression fittings, ground fittings, and rubber seals.

 

Due to the fact that it’s slippery, it enables connections to move together appropriately for a good seal. And, if you make use of a type that doesn’t harden, disassembly and repair will be much easier years later. Some kinds of dope harm plastic parts, so inspect the label.

Don’t Fight It, Replace It

Don’t Battle It, Replace It

If you really feel a groove where the O-rings mate to the spout, the faucet is toast. Don’t waste anymore time and energy on O-ring repairs– you’ll never get a long-lasting seal. We highly advise replacing the faucet.

 

Get a Better Grip

Get a Better Grip

Use a hex socket and valve grinding compound to avoid stripping the set screw.

 

Squeeze the hex socket deep into the setscrew with one hand and pull the ratchet handle with the other. After that loosen up the setscrew with a quick yanking action.

Some jobs are better left to the pros...

Get No-Commitment Estimates For Your Project

Proud to Install, Repair, and Service the Following Brands: